5/18/2013

etched galvanized steel painting


etched galvanized steel painting

Cleaning
Solvent cleanup


Mineral spirits, turpentine, high-flash hydrocarbon and alternative typical cleanup solvents are often used, provided they're applied with lint-free rags or soft-bristled, nylon brushes often modified to avoid re-spreading contaminants. when cleanup, surfaces ought to be completely rinsed with quandary and allowed to dry.

Because some solvents might react otherwise with completely different paint systems, consult the paint manufacturer for specific cleanup directions.
Alkaline answer cleanup

Oil, grease associate degreed dirt are often removed by mistreatment an alcalescent answer within the hydrogen ion concentration vary of 11-12, however not bigger than thirteen. the answer are often applied via dipping, spraying or brushing. If brushing, a soft-bristled, nylon brush is usually recommended. If dipping or spraying, the answer temperature ought to be between 140-185 F (60-85 C).

For fresh galvanized surfaces, a water-based wetting agent are often accustomed take away contaminants. when cleanup, completely rinse the surface with quandary and permit complete drying.
Ammonia cleanup


A solution of 1-2% ammonia applied with a nylon brush also can be used, though this methodology generally is reserved for cleanup components with ash residue. when cleanup, completely rinse the surface with quandary and permit complete drying.
Profiling

In order to produce an honest adhesion profile for the paint, the galvanized surface should be freed from protrusions associate degreed slightly cracked to produce an anchor profile. Hand- or power-tools are often accustomed take away any high spots. Care ought to be taken to get rid of as very little metal as doable.

In order to change surface the generally sleek galvanized surface, associate degree abrasive sweep- or brush-blast is also used. Blast material particle size for identification galvanized steel ought to vary between eight-20 mils (200-500 microns). Aluminum/magnesium salt has been used with success to sweep-blast-profile galvanized steel. Organic media like dried corncobs, dried walnut shells, corundum, rock and mineral sands with a Moh’s hardness of 5 or less may additionally be used.

The temperature of the galvanized half once blasting will considerably have an effect on the finished surface profile. Sweep-blasting whereas the galvanized half remains heat (175-390 F [79-199 C]) provides a wonderful profile. counseled close conditions for sweep-blasting area unit but five hundredth ratio and a minimum temperature of seventy F (21 C).
Sealers

Penetrating sealers area unit generally a 2-part epoxy that forms a coating some two mils (50 microns) thick. they need been used as a surface treatment methodology on a lot of difficult-to-clean surfaces like partly worn galvanized steel. Follow manufacturer directions for application; continually use a overcoat over the sealer.
Conversion Coatings

Phosphate answer is employed as a conversion coating which will increase the adherence and sturdiness of the paint or powder coating. The phosphate treatment are often applied by immersion, spray or a soft-bristled nylon brush. The phosphate ought to solely be left on the
galvanized steel between 3 to 6 minutes. The piece ought to then be rinsed with clean water and allowed to fully dry.
Primers

Wash primers use a metal conditioner to neutralize surface oxides and hydroxides, likewise as print the galvanized surface. Wash primers ought to be applied to the galvanized surface at thickness between zero.3-0.5 mils (eight-13 microns). Thicknesses on top of zero.5 mils (13 microns) will cause poor adhesion. thanks to this, wash primers area unit best applied in search conditions, not within the field. Follow manufacturer directions for optimum performance.
Acrylic Passivation

Acrylic passivation is that the application of associate degree acidic acrylic answer to passivate the galvanized surface and promote paint or powder-coat adhesion. Acrylic passivation merchandise ought to be applied some zero.04 mils (one micron) thick to a clean galvanized surface. The coating ought to be fully dry before painting or powder coating.
Determing the Presence of Passivation Agents

Although some passivation-quenched galvanized surfaces have a duller, matte grey end, it are often tough to visually discover whether or not passivation merchandise are used. If there's uncertainty concerning whether or not the steel was quenched, the galvanized surface must be tested for the presence of passivation agents. This testing is fairly clear-cut and is represented in ASTM B 201.


4/30/2013

How to Paint Metal

Most amateur homemade enthusiasts don’t acumen to color metal surfaces and their best efforts tend to supply ugly finishes that ultimately peel away. you can not paint metal as you'd drywall of wood things, as a result of vacant metal surfaces won't bond with oil or latex paints. Learn the correct thanks to generate an enduring end on metal things, or paint failure can eventually follow.

Priming Metal

Before making an attempt to color metal surfaces, like doors, area chairs, roofs, cupboards or siding, apply AN acid-based metal etching primer. Once the metal surface is ready, it'll settle for most any sort of paint.

Painting Metal

Painting metal is straightforward once the surface is correctly conditioned with AN etching primer base. Most amateurs like better to roll paint over metal surfaces. sadly, this typically results in ugly roller marks within the end. For a slick end, sleek the wet paint, employing a polyester applier.

Spray Painting Metal

Spray painting metal is that the solely thanks to guarantee a professional-looking end. as a result of metal is slick, it'll reveal brush strokes and roller marks. Spray cans area unit well-suited for painting smaller auriferous things. If you would like to color an oversized metal surface, rent a sprig rig.

Painting Galvanized Metal

Galvanized metal contains a layer of metallic element that inhibits rust. fortuitously, this layer isn't greaseproof to straightforward metal-etching primers. Painting galvanized metal isn't any harder than painting the other metal surface, like steel, atomic number 26, aluminium or tin.

Best Paint for Metal Surfaces

Once auriferous surfaces area unit ready, they’ll settle for most any paint. there's no best paint for metal surfaces; but, some area unit higher suited to bound styles of metal. Paint metal siding with AN acrylic latex paint; paint metal furnishings and the other surfaces subject to force, exploitation enamel.

8/10/2012

How to Paint a Galvanized Metal Pig

How to Paint a Galvanized Metal Pig
Galvanized metal is coated with a layer of atomic number 30 that protects the surface from rust. sadly, this method makes the metal extremely proof against adhesion. If you want to color a galvanized ornament or sculpture of a pig, you may have to be compelled to prepare the metal to form it additional receptive to color adhesion by coating it with a selected sort of primer that may change surface the surface, or the paint can chip shortly once initial application.



1.  Clean the galvanized metal pig employing a degreaser. Rinse the pig completely, and permit the metal to dry before continuing.
2. Take the pig to a well-ventilated space, and place it on a drop material.


3. shield areas of the galvanized pig you are doing not wish painted by covering them with skilled painter's tape.
4. Spray on a coat of bimetallic etching primer. Hold the dispenser regarding eight inches from the galvanized pig. Coat the exposed space. Wait one hour for the etching primer to dry, then flip the metal pig over, and prime the opposite aspect. Wait six hours for the etching primer to cure.
5.Spray a high-gloss acrylic paint onto the ready bimetallic pig within the same means you applied the etching primer. Wait 2 hours for the galvanized pig to dry.

4/15/2012

How to Paint Galvanized Steel

How to Paint Galvanized Steel
Galvanized steel needs special surface preparation before painting. The steel has been treated with a special zinc coating to cut back rust. This coating should be properly cleaned and roughened for the most effective adherence of the primer before painting. A well-done paint job on galvanized steel can last an extended time while not peeling or flaking. the extra protection offered by the paint additionally ought to facilitate prolong the lifetime of the piece by staving off rust and corrosion.
Instructions

 one     Wash the galvanized steel with hot soapy water and rinse with hot water. permit it to dry completely.
 a pair of create an answer of one to a pair of p.c ammonia with water by mixing equal elements of water and ammonia. Household ammonia is approximately five to ten p.c ammonia therefore cutting the quantity of ammonia in 0.5 ought to yield an answer that's robust enough to arrange the zinc for painting. Rinse with hot water and permit it to dry fully.

3 Use 240 grit sandpaper and sand the complete surface. If there are handles or elements which will be removed, take away them and sand every half separately. If the half can not be removed as a result of it's welded or riveted to the most piece, make sure to urge the sandpaper into each crevice moreover as you'll.
4 Wipe the complete piece down with a tack cloth. A tack cloth is offered within the painting section of most hardware stores. it's a cloth that encompasses a sticky substance inbuilt to select up all the fine sanding mud to arrange surfaces for painting.
5 Spray metal primer over the complete surface. Work in sleek strokes from high to bottom to avoid runs, sags and drips. permit it to dry fully in step with the counseled drying time printed on the primer will label.
6 examine for runs, drips or sags. If needed, sand any imperfections and apply a coat of primer to the world.
7 Spray the complete surface with metal paint of identical whole because the primer. every whole of primer and paint are formulated to figure best along. Work in sleek strokes from high to bottom to avoid runs, sages and drips. permit it to dry fully in step with the counseled drying time printed on the paint will label.
8 examine for runs, drips or sags. If needed, sand any imperfections and apply a coat of paint to the world.

4/09/2012

How to Spray Paint sort of a professional

How to Spray Paint sort of a professional
How to Spray Paint sort of a professional

Instructions

        1 begin by removing the half that has to be painted. (You may tape around it, however take care concerning overs pray)

        2 Sand the half with the three hundred grit sand paper till the surface may be a very little rough. this can be necessary for the primer to bond with the surface. once sanding wipe down the half with micro fiber cloth.

        3 gently spray the half with primer. a couple of lightweight coats are higher than one serious coat. certify to permit correct drying time between coats.

        4 once a couple of lightweight coats of primer are applied, wetsand with the 800 grit sandpaper. once wet sanding, wipe once more with micro fiber cloth.

        5 currently it's time to use the colour. When spraying the spray paint certify to use sleek even passes across what's being painted. don't begin painting on prime of the half as a result of the paint are going to be heavier in that space. When painting you would like to press and unleash the button to the facet of the merchandise being painted. once more a couple of lightweight coats are higher than one serious one and certify to permit correct drying time between coats.

        6 once you're glad with the colour, wetsand with 800 grit sandpaper and then wipe with micro fiber cloth.

        7 currently it's time for the clear coat. Spray the clear coat a similar manner because the spray paint. just one or 2 lightweight coats are required. enable the clear coat many time to dry as this can be the layer that you simply can see most. you do not need any fingerprints on your final surface!

        8 once the clear coat has had over enough time to dry, You currently need to wetsand with the 800 grit, then the one thousand grit, then 1200, then 1500, and at last the 2000 grit sandpaper. this could take away any heavier spots within the clear coat and can polish your painted product up terribly nicely.

        9  Next you wish to get rid of the scratches left by the 2000 grit. For this you may got to buff the surface with rubbing compound.

        10 currently you wish to buff the surface with a medium cut polish to present the surface a pleasant glassy look.

        11 whether or not or not it's exterior or interior elements that are painted, I perpetually add a handful coats of wax to the surface. This acts as a protectant to the clearcoat and offers it a pleasant sleek feel and additionally helps repel dirt.

11/18/2011

Save Wagner 518080 Control Spray Max HVLP Sprayer

Wagner 518080 Control Spray Max HVLP Sprayer

List Price: $129.99Price: $108.24 & this item ships for FREE with Super Saver Shipping. Details
You Save: $21.75 (17%) 

In Stock.
Ships from and sold by Amazon.com. Gift-wrap available.

READ REVIEW
.............................................................................................................................

Customer Reviews

9/16/2011

galvanized metal etching spray primer

Most amateur do-it-yourself enthusiasts don’t shrewdness to color metal surfaces and their best efforts tend to provide ugly finishes that ultimately peel away. you can not paint metal as you'd drywall of wood things, as a result of clean metal surfaces won't bond with oil or latex paints. Learn the correct thanks to generate an enduring end on metal things, or paint failure can eventually follow.
      
  

Priming Metal

Before trying to color metal surfaces, like doors, patio chairs, roofs, cupboards or siding, apply an acid-based metal etching primer. Once the metal surface is primed, it'll settle for most any sort of paint.

Painting Metal

Painting metal is straightforward once the surface is correctly conditioned with an etching primer base. Most amateurs favor to roll paint over metal surfaces. sadly, this generally results in ugly roller marks within the end. For a slick end, sleek the wet paint, employing a polyester paintbrush.

Spray Painting Metal

Spray painting metal is that the solely thanks to guarantee a professional-looking end. as a result of metal is slick, it'll reveal brush strokes and roller marks. Spray cans are well-suited for spray painting smaller metallic things. If you wish to color an oversized metal surface, rent a twig rig.

Painting Galvanized Metal

Galvanized metal features a layer of zinc that inhibits rust. Fortunately, this layer isn't impervious to straightforward metal-etching primers. Painting galvanized metal is not any harder than painting the other metal surface, like steel, wrought iron, aluminum or tin.

Best Paint for Metal Surfaces

Once metallic surfaces are primed, they’ll settle for most any paint. there's no best paint for metal surfaces; but, some are higher fitted to sure sorts of metal. Paint metal siding with an acrylic latex paint; paint metal furniture and the other surfaces subject to duress, using enamel.

How to Paint a Galvanized Metal
Galvanized metal is coated with a layer of zinc that protects the surface from rust. sadly, this method makes the metal highly immune to adhesion. If you would like to color a galvanized ornament or statue of a pig, you may have to be compelled to prepare the metal to create it additional receptive to color adhesion by coating it with a specific sort of primer which will roughen the surface, or the paint can flake off not long when initial

 one Clean the galvanized metal pig employing a degreaser. Rinse the pig totally, and permit the metal to dry before continuing.
 a pair of Take the pig to a well-ventilated space, and place it on a drop cloth.
 three defend areas of the galvanized pig you are doing not need painted by covering them with skilled painter's tape.
 four Spray on a coat of metallic etching primer. Hold the spray will concerning eight inches from the galvanized pig. Coat the exposed space. Wait one hour for the etching primer to dry, and then flip the metal pig over, and prime the opposite facet. Wait six hours for the etching primer to cure.
 five Spray a high-gloss acrylic spray paint onto the primed metallic pig within the same method you applied the etching primer. Wait 2 hours for the galvanized pig to dry.